Wind Line

Fancoil Ceiling model, including minium temperature thermostat.Removable cover made in pressed sheet steel, painted RAL 9010 colour. Its exterior design is distinguishedby the wide angled corners.Inside structure in galvanized sheet panels, with inside walls heat insulated and anti-condensation coated.Exchange battery with copper tubes mechanically expanded into aluminium fins and brass hydraulicattachments (1/2” GF), complete with air valve. Standard 3 rank battery, fitted with left hand attachments,however during installation the attachments can be moved to the right. Max. running pressure is 10 bar.Fan unit with a three speed single-phase motor, coupled to 1, 2 or 3 centrifugal double suction fans,depending on the size of the fan-coil heater. The fans are in pressed aluminium and perfectly dynamicallybalanced to guarantee extremely quiet running.Filter made from a metal frame and a filter held by a fine metal mesh, it is easy to remove and wash.Control board contains the electric and electronic regulation devices and the connection terminal board(230V 50Hz); it is fitted standard on the left side. Controls can be reached by opening the flap in the cover.Air diffusion guaranteed evenly through the ABS heat-resistant curved blade elements, and the flowdirection can be changed if wished.Standard minimum thermostat this internal component allows ventilation during heating phases, butonly when the exchange battery has heated up.

Model with right or left fittings • construction detailsBearing structure: galvanized steel 10-12/10 thick, body internally insulated with hygroscopic panels,heat insulating, sound deadening and selfextinguishing (class 1 - 30 mm thick), complete with deliveryand recovery flanges with a rectangular duct joint.Standard heat exchange coil: 4 ranks divided in two circuits for 4 tube system, the first with 3 ranksfor air conditioning, the second with 1 rank for heating. High capacity heat exchangers, with coppertubes mechanically expanded into aluminium fins, complete with brass fittings and anti-torsion plate.Maximum running pressure of 10 Bar.Fan assembly: formed of a radial fan with single or double fan wheel, with static and dynamic balancing,directly coupled to the driving shaft. Electric single phase motor with permanent condensationand thermal protection. The low number of revs, large diameter fan and the special insulating that isused give excellent performance with a very low sound output.Filtering assembly: in recyclable acrylic, selfextinguishing (class 1), mounted on a galvanised plateframe with protection net, removable for periodic cleaning.

Units are assembled in a galvanised sheet metal structure lined with soundproofing material. The heatexchangers are of the finned block type with copper pipes and aluminium fins. Fan unit consists of anelectric double-section centrifugal fan with a directly-coupled three-speed motor.Ventilation may be controlled through a control panel designed for wallmounting (accesory) available in theversion with just speed selector switch or integrated with room thermostat.ModelsTAW/O: horinzotal air conditioning unit with water battery.TAW/V: vertical air conditioning unit with water battery.TAE: direct expansion air conditioning unitSFA: filtering section (optional).

Directly coupled motor 4 models from 1000 m3/h to 4000 m3/h. The RT recovery units have many applications in publiclocals,where the presence of smoke or crowds of people make continuosair change essential.They are available in horizontal (H) or Vertical version (V), theframe is made of extruded anodised aluminium profiles,singlepanel insulated (SP) or double zinc panels thickness 23 mminsulated with 45 Kg/m3 density poliuretan (DP).The dual intake centrifugal fans have directly-coupled, three speedsingle phase 220V/50Hz motors with external rotor;the heatrecovery unit is a static cross-flow system with aluminium platesand cell filters with syntethic septum, efficiencyEU4.ModelsRT/H: heat recovery unit, horizontal versionRT/V: heat recovery unit, vertical version

Directly coupled motor13 models - flow rates from 800 m3/h to 7900 m3/h.All the model use centrifugal dual intake electric fans with forward blades directly coupled with a 1 speed motor :220V,1Phase 50-60Hz 4 or 6 pole IP 20 or IP55protection, depending from models.The frame is made from Aluzink or AISI 304 stainless steel; a suitably thick layer ofpoliester is added as soundproofinginsulation.The operating temperature range is from -20¡C to + 40¡C

Directly coupled motor 8 models - flow rates from 200 m3/h a 6500 m3/h. The EAT SIL series extraction units featureextremely low operating noise.The series includes 8 models with directly coupled fans.Thanks to the different combinations of impeller diameter,rotationspeed and power supply, our range covers field offlow-rates from 200 m3/h to 6500 m3/h with working pressure upto 45 mm.w.c.The electric fans are available in single or dual intake versions, with statically and dynamically balanced impellerstominimise the transmission of noise. The high working pressures ensures the extraction or inlet of air in a seriesofrooms.The structure is made from aluzink, with perforated internal panelling; a 50 mm layer of soundproofing material(glasswool) is installed between the panels.The electric fans(single or dual intake) have forward blades, with externalimpeller motors, except for model EAT SIL450T which has built-in thermal contact for the motor. Vibration damping munts are installed between the structureand the fan, to attenuate the transmission of any vibrations. The fan can beinspected and removed from above.

Belt transmission motor 8 models - flow rates from 1500 m3/h to 30000 m3/h.All the models have dual intakes centrifugal fan with forward blades completed with vibration-damping joint on theoutlet, one or two asynchron triphase motor with cage-rotor, protection degree IP55 and winding in F class, accordingto IEC 34-1 and IEC 72 norms, assembled on a suitable belt-tighter slide.The assembling of the fan and of the motor is on a only amortised base. The Drive is by pulleys and V- belts. Thecase is made of extruded anodised aluminium profiles and double zinc panels thickness 23 mm, insulated with 45Kg/m3 density poliuretan.

Directly coupled motor 5 model from 1000 m3/h to 4000 m3/h Horizontal (H) and Vertical (V) versions.Four model available, (air flow from 1000 m3/h to 4000m3/h), Horizontal (H) and Vertical (V), they are created inasingle unit, the frame is made of extruded anodised aluminium profiles and double zinc panels thickness 23 mm,insulated with 45 Kg/m3 density poliuretan. Filtering section is realised with filtering material in polyester, G4 class(efficiency 90,1% weighted),metallic frame and containing electro-solded net. Water heating and cooling coils aremade in Copper-Aluminium, mechanically mandrelled, with frame in zinc-plate and collectors in steel with threadedjunctions,and the tight is tested into the water at the pressure of 30 Ate using dry air. These models have centrifugalfan with double intake a forward blades, directly coupled mono phase motor 230 V - 50Hz 3 speed.

Belt transmission motor 9 model from 1700 m3/h to 25000 m3/h Horizontal (H) and Vertical (V) versions. Nine modelavailable, Orizzontal and Vertical, they are created in a single unit, the frame is made of extruded anodised aluminiumprofiles and double zinc panels thikness 23 mm, insulated with 45 Kg/m3 density poliuretan. Filtering section isrealised with filtering material in polyester, G4 class (efficiency 90,1% weighted), metallic frame and containingelectrosolded net. Water heating and cooling coils are made in Copper-Aluminium, mechanically mandrelled, withframe in zinc-plate and collectors in steel with threaded junctions, and the tight is tested into thewater at the pressureof 30 Ate using dry air. All the models have centrifugal fan with double intake a forward blades completed withantivibrateing junction on the pressing mouth, asynchrony triphase motor with cage-rotor, protection degree IP55 andwinding in F class, according to IEC 34-1 and IEC 72 norms, assembled on asuitable belt-tighter slide. The assemblingof the fan and of the motor is on a onlyamortised base. The Drive is by pulleys and V- belts.The unit is also fittedwith a safety micro-switch and protective net.

Fan coil wall fitted version, including minimum temperature thermostat, three speed switch, summer-winterselection switch, room thermostat (AB and CBE version). Automatic operations (CBE version).Removable cover made in pressed sheet steel, painted RAL 9010 colour. Its exterior design is distinguishedby the wide angled corners.Inside structure in galvanized sheet panels, with inside walls heat insulated and anti-condensation coated.Exchange battery with copper tubes mechanically expanded into aluminium fins and brass hydraulicattachments (1/2” GF), complete with air valve. Standard 3 rank battery, fitted with left hand attachments,however during installation the attachments can be moved to the right. Max. running pressure is 10 bar.Fan unit with a three speed single-phase motor, coupled to 1, 2 or 3 centrifugal double suction fans,depending on the size of the fan-coil heater. The fans are in pressed aluminium and perfectly dynamicallybalanced to guarantee extremely quiet running.Filter made from a metal frame and a filter held by a fine metal mesh, it is easy to remove and wash.Control board contains the electric and electronic regulation devices and the connection terminal board(230V 50Hz); it is fitted standard on the left side. Controls can be reached by opening the flap in the cover.Air diffusion guaranteed evenly through the ABS heat-resistant curved blade elements, and the flowdirection can be changed if wished.Standard minimum thermostat this internal component allows ventilation during heating phases, butonly when the exchange battery has heated up.

Fan coil recessed model, including minimum temperature thermostat. Removable cover made in pressed sheet steel, painted RAL 9010 colour. Its exterior design is distinguishedby the wide angled corners.Inside structure in galvanized sheet panels, with inside walls heat insulated and anti-condensation coated.Exchange battery with copper tubes mechanically expanded into aluminium fins and brass hydraulicattachments (1/2” GF), complete with air valve. Standard 3 rank battery, fitted with left hand attachments,however during installation the attachments can be moved to the right. Max. running pressure is 10 bar.Fan unit with a three speed single-phase motor, coupled to 1, 2 or 3 centrifugal double suction fans,depending on the size of the fan-coil heater. The fans are in pressed aluminium and perfectly dynamicallybalanced to guarantee extremely quiet running.Filter made from a metal frame and a filter held by a fine metal mesh, it is easy to remove and wash.Control board contains the electric and electronic regulation devices and the connection terminal board(230V 50Hz); it is fitted standard on the left side. Controls can be reached by opening the flap in the cover.Air diffusion guaranteed evenly through the ABS heat-resistant curved blade elements, and the flowdirection can be changed if wished.Standard minimum thermostat this internal component allows ventilation during heating phases, butonly when the exchange battery has heated up.